Please read this all when you get the chance, thank you....
Having looked at this further, when using "use console rain", it looks like its reverting back on the hour every hour in b120 as opposed to reverting back instantly in b131.
Nothing i can do to change that, that i have found, this years total rainfall should now be 586.0mm
This is whats on the console, i have tried setting this in WLL setup but under Rain in the app is says 585.8mm
IN the records at the bottom it only says 119.8mm, perhaps thats what WLL has actually recorded since i installed and totally disregarding the updated total that i added in the setting, looks like there's perhaps yet another bug in the WL app, i will report that to support. Nonetheless, adding the 119.8 to 585.8 does not add up to the 740'ish amount that WD is reverting too, but then if you add in this months rain at 31.4 it does come a bit closer to the 740'ish amount, still not the same amount though.
I think perhaps in this instance, figuring out the original issue of WD recording 0.3mm per tip. Its set to 0.2mm in WD on the station setup page and its also set to 0.2mm in WLL as that is showing 31.4mm for this month so that has to be correct and i didn't have this issue with the console connected so its deffo sommat to do with WLL.
Your WLL windows app, i tried on my main laptop and runs great, interestingly, that's where the erroneous rainfall amounts are showing 39.9mm month and 744mm year. these do not show anywhere else, not on WL not in the WLL app and not on Mobilize, where is this rainfall coming from?
{"data":{"did":"001D0A7153E4","ts":1634195124,"conditions":[{"lsid":454287,"data_structure_type":1,"txid":1,"temp": 52.9,"hum":89.8,"dew_point": 50.0,"wet_bulb": 51.2,"heat_index": 52.9,"wind_chill": 52.9,"thw_index": 52.9,"thsw_index": 50.9,"wind_speed_last":2.00,"wind_dir_last":231,"wind_speed_avg_last_1_min":2.00,"wind_dir_scalar_avg_last_1_min":250,"wind_speed_avg_last_2_min":2.68,"wind_dir_scalar_avg_last_2_min":253,"wind_speed_hi_last_2_min":6.00,"wind_dir_at_hi_speed_last_2_min":276,"wind_speed_avg_last_10_min":2.06,"wind_dir_scalar_avg_last_10_min":253,"wind_speed_hi_last_10_min":7.00,"wind_dir_at_hi_speed_last_10_min":256,"rain_size":2,"rain_rate_last":0,"rain_rate_hi":0,"rainfall_last_15_min":0,"rain_rate_hi_last_15_min":0,"rainfall_last_60_min":0,"rainfall_last_24_hr":0,"rain_storm":0,"rain_storm_start_at":null,"solar_rad":40,"uv_index":0.0,"rx_state":0,"trans_battery_flag":0,"rainfall_daily":0,"rainfall_monthly":157,"rainfall_year":2929,"rain_storm_last":12,"rain_storm_last_start_at":1634047380,"rain_storm_last_end_at":1634162460},{"lsid":454288,"data_structure_type":2,"txid":2,"temp_1": 54.2,"temp_2": 54.1,"temp_3":null,"temp_4":null,"moist_soil_1":200.0,"moist_soil_2":null,"moist_soil_3":null,"moist_soil_4":null,"wet_leaf_1":0.1,"wet_leaf_2":null,"rx_state":0,"trans_battery_flag":0},{"lsid":454286,"data_structure_type":4,"temp_in": 64.8,"hum_in":68.5,"dew_point_in": 54.2,"heat_index_in": 64.7},{"lsid":454285,"data_structure_type":3,"bar_sea_level":30.245,"bar_trend":-0.021,"bar_absolute":30.202}]},"error":null}
When i try to use that windows app on my weather server laptop i get this error
{"data":{"broadcast_port":22222,"duration":86400},"error":null}
Parsed Port 22222,"dur
Parsed Port ->22222<-
Could not bind socket.
The above binding issues is why i cannot see the middle window in when i try to auto detect WLL in wd...
The firewall is all turned off on that laptop, I've just done it, also that port is forwarded in my router settings.
So i am at a loss at present for 2 things, one is the rainfall issue and the other is port bind error...
EDIT;
This is very weird, i think i have found a workaround, it took me quite a while to get to the correct yearly
rain amount to put into WLL settings so that it comes out right and that number was 438.7mm, as see here
{"data":{"did":"001D0A7153E4","ts":1634209548,"conditions":[{"lsid":454287,"data_structure_type":1,"txid":1,"temp": 57.7,"hum":80.9,"dew_point": 51.9,"wet_bulb": 54.1,"heat_index": 57.7,"wind_chill": 56.6,"thw_index": 56.6,"thsw_index": 57.5,"wind_speed_last":8.00,"wind_dir_last":259,"wind_speed_avg_last_1_min":4.81,"wind_dir_scalar_avg_last_1_min":253,"wind_speed_avg_last_2_min":5.62,"wind_dir_scalar_avg_last_2_min":258,"wind_speed_hi_last_2_min":11.00,"wind_dir_at_hi_speed_last_2_min":232,"wind_speed_avg_last_10_min":6.62,"wind_dir_scalar_avg_last_10_min":251,"wind_speed_hi_last_10_min":15.00,"wind_dir_at_hi_speed_last_10_min":267,"rain_size":2,"rain_rate_last":0,"rain_rate_hi":0,"rainfall_last_15_min":0,"rain_rate_hi_last_15_min":0,"rainfall_last_60_min":0,"rainfall_last_24_hr":0,"rain_storm":0,"rain_storm_start_at":null,"solar_rad":84,"uv_index":0.0,"rx_state":0,"trans_battery_flag":0,"rainfall_daily":0,"rainfall_monthly":157,"rainfall_year":2192,"rain_storm_last":12,"rain_storm_last_start_at":1634047380,"rain_storm_last_end_at":1634162460},{"lsid":454288,"data_structure_type":2,"txid":2,"temp_1": 56.5,"temp_2": 142.0,"temp_3":null,"temp_4":null,"moist_soil_1":200.0,"moist_soil_2":null,"moist_soil_3":null,"moist_soil_4":null,"wet_leaf_1":0.1,"wet_leaf_2":null,"rx_state":0,"trans_battery_flag":0},{"lsid":454286,"data_structure_type":4,"temp_in": 65.0,"hum_in":67.8,"dew_point_in": 54.1,"heat_index_in": 64.8},{"lsid":454285,"data_structure_type":3,"bar_sea_level":30.199,"bar_trend":-0.033,"bar_absolute":30.157}]},"error":null}
that then gives me the correct amount in WD at 556.7mm (now), thats the amount of all the months this year
added up in WD. Whats even more strange is that that amount is actually lower than what my console says (586.0mm)
but i am going to stick with the amount that WD adds up to of which is the 556.7, shouldnt be mind cause its
an odd number, i have a feeling i have lost some rain amounts in WD somewhere and gained some due to WDs
0.3 tip measure. not overly worried about that as long as its right from here on in.
I would very much prefer WD to do the work though, so if you can figure out why WD is measuring 0.3mm per tip
thats would be great, i can let you have whatever you need and work together to try to resolve it. I wonder if its
a calculation thing what with WLL being in inches in that code above, its also not including a decimal, you can see that
here rainfall_monthly":157,"rainfall_year":2192,
it should be rainfall_monthly":15.7,"rainfall_year":21.92,
but even that converted to mm still does not match what i had to put into WLL to get that amount and that was the 438.7mm
Go figure that cause i cant wrap my head around it lol how does inputting 438.7mm into WLL yearly rain setting
come out at 21.9in, it doesnt , so thats one more issue i have to get on at Davis about.