Weather Station Hardware > Davis Instruments Weather Stations
Trouble Shooting Vantage Pro, no data from the ISS.
J0e:
Hello.
I need help to troubleshoot my Vantage Pro transmitter. :?
The problem started with early morning data loss. Just before sun rise, all data from the transmitter would cease. After I would notice this and hit the "done, - " button combination on my display, I could re-acquire the signal. For a day or so. Then it would happen again.
A few days ago the signal stopped and I have not been able to regain it.
I checked the battery and it was nearly dead. Had a little over 1 volt in in it. Thing is though, I just replaced that battery this spring.
This sounds like the VP2's super cap failure but the VP1 has a different capacitor and I have not heard anyone mention this sort of failure with that model. I pulled the board off and looked at it and the capacitor ( 5.5volt, 1F) does have a very little bit of a substance on one side (the cap is flat and round - about the size of 3 quarters taped together) that looks like dried honey but it doesn't appear damaged.
I had an older CR123a battery that still had 2.5 volts in it so I stuck that in this morning but I still have no signal.
I have also tried running the transmitter without battery hoping the Solar Panel could do the job but that didn't work either.
So -
Does this sound familiar to anyone?
Does anyone know if there is a test point on the VP1 I could use to check the solar panel voltage?
Any and all tips are really appreciated.
J0e
J0e:
Is there a prize for stumping the forum :grin:
So by way of update.
In order to see if a fresh battery would bring the ISS back to life, I went to Radio Shack and found 2 CR123 Li-ion rechargeable batteries with a charger, on sale for $10 (US).
Sadly, the batteries won't seem to charge.
However, in messing around with the ISS I decided that the connector on the solar panel's cable wasn't fitting very snuggly. So I jammed a bit of multi-strand wire down in the connector and then jammed the ISS's connector pins down into the wire.
The Result is that now I have wind data reporting and a message that says "Low Battery". Still no data from Temp/Humidity.
Thoughts?
Anyone? Anyone? Bueller?
ocala:
Sorry, just don't have any experience with the VP1.
It sounds like you have a solar panel issue based on what you did.
I think you need to forgo those rechargeable CR123's and go with a standard battery.
Also a 2.5 volt CR123 is dead.
If you have a meter point that solar panel at the sun and see what it's putting out. Then find out from Davis what the output should be.
As for the temp/humid sensor, I don't have a clue.
Good luck with your problem and let us know if you find a fix.
kray1000:
The supercap shouldn't have any "substance" on it.
You probably know this already, but just in case, the rechargeable batteries won't be charged while in the ISS. But using a battery without the solar panel should have worked fine. You may have a bad transmitter board in the ISS. At the very least, the supercap should be replaced.
The solar panel wire connector is poorly designed in my opinion. In my VP2, intentionally squeezing the clips and bending the wires barely keeps it connected.
I believe I've heard that in the absence of a capacitor and a solar panel, the battery alone will power the ISS for about eight months. A (verified) fresh battery should get the data flowing. If you can't find any breaks or loose connections in the cables, it may be time for Davis to recondition your unit.
The "Low Battery" message will persist until the console is run through setup mode, or until midnight. Or maybe longer. Your kilometerage may vary.
I agree that a standard, non-rechargeable battery would probably work best. I believe the battery will work until the voltage drops to around 3.6 volts, give or take, so as stated, a 2.5 volt battery won't work. Try using a new non-rechargeable battery.
wxtech:
I have a VP original on my work bench. A CR123 measuring 2.48 volts won't transmit even to the console a few inches away. A CR123 measuring 2.69 volts transmits from my second floor and has the message 'Low battery on station 1'. With no solar panel connected, I measure 2.69 volts also across the super cap while the SIM is operating. I have a large supply of unused CR123A; the highest voltage measured is 3.28 volts.
The super cap in the VP is constructed with a steel case. It's mounted/soldered on two tabs that are spot welded to the cap case and are .21" wide. This super cap has no wires.
I see some dark corrosion (rust) on the positive side of the cap. The cap/board solder point has white peeling board coating similar to peeling coating on the U29. This white material is not from the super cap.
*****************************
Next experiment.
I connected a solar panel to the VP and exposed it to a fluorescent work light. The super cap voltage measured 2.81 volts. I removed the CR123. The SIM continued to transmit to the console after 10 minutes now & the super cap voltage has dropped to 2.71 volts (2.65v in 15 minutes). No battery, no light on the solar panel.
Navigation
[0] Message Index
[#] Next page
Go to full version