Weather Station Hardware > AcuRite Weather Stations

Atlas WiFi Display Design Problem (IMO)

(1/2) > >>

wags1:
I have been struggling for some time now with what seemed to be disconnects of my Atlas WiFi display from my network. I would get the red "X" below the WiFi icon on the Atlas display and data would stop being reported to both MyAcurite as well as WU. AcuRite support had me jump thru all the usual hoops and even replaced both my Atlas sensor as well as the WiFi display under warranty. None of it resolved the issue.

When the problem would occur I could see in my router log that the WiFi display was disconnecting and reconnecting from my router approximately every 10 seconds (that time frame was an important clue). One of the features of the Atlas WiFi display is "rapid fire" updates of weather data that occur every 10 seconds. I figured that could not be a coincidence and after thinking about it a bit I decided to try an experiment. This morning after the WiFi connection had been solid for an hour or 2 and I had no disconnects/reconnects from the WiFi display in my router log I unplugged my cable modem but left my router connected. Roughly 10 seconds or so after unplugging my cable modem (effectively disconnecting the internet) the constant disconnects/reconnects at 10 second intervals began again. They stopped shortly after plugging my cable modem back in (effectively reconnecting the internet).

The net is that when the Atlas Wifi display can't reach the Acurite server(s) that it uses to send the weather data, instead of continuing to try and maybe report an error it starts to disconnect and reconnect over and over again from the router. Not only is that very poor design, IMO, but worse than that is the fact that apparently the Acurite support folks aren't aware of that fact and blame the problem on something in the customers network or, even worse for them as in my case, replace their own equipment to resolve a problem that is due to the way their product works. No other WiFi connected device that I own, or have owned, works that way.

I sure hope Acurite can figure out a way to fix this problem with a FW update. At the very least they need to make sure that their support personal understand this issue for what it is.

wags1:
Just a final update. I went back to using my AcuRite Access that I saved from when I was using my Iris sensor. It works perfectly with none of the issues that the WiFi displays have and is sending weather data to MyAcurite and WU 24x7 without any glitches whatsoever. AcuRite sent me 2 replacement WiFi displays, the last of which they said they “tested” before they sent it to me. They all had exactly the same issue as described in my OP. I’m still using 2 of them in different locations in my house as they work fine and have a stable WiFi connection as long as you don’t try to use them to send weather data to MyAcurite and/or WU. It’s unfortunate but AcuRite really needs to solve the issue with the WiFi display.

AlanD96:
wags1 -
It's not just the wi-fi displays which disconnect, every single one of my old model Atlas displays exhibit the same behavior.  Full bars, then the bars slowly disappear for anywhere from 30 seconds to an hour.  And at the same time my 'Access' which is feeding Weather Underground never loses its connection.

You actually did me a favor.  I was going to purchase one of the new display models, figuring that by now they must have figured out this problem
Apparently not. 

wags1:
AlanD96 -
The sad part is AcuRite had me chasing my tail for over a month insisting that the problem was my network, the distance to my sensor, etc.. The only good thing to come out of it is that they sent me a brand new Atlas sensor and 2 new Wifi displays. They still insist that their equipment is just fine…🤣

DoctorKnow:
I think someone figured out why the signal comes and goes. The main board in the Atlas reboots every so often. Don't know why. Someone in another thread recommended disconnecting the fan.

Navigation

[0] Message Index

[#] Next page