Author Topic: Replacement parts for Ambient Weather WS-1001 Clone - Maplin N23DQ  (Read 1617 times)

0 Members and 1 Guest are viewing this topic.

Offline Aircub

  • Member
  • *
  • Posts: 29
Hi I have a Maplin Maplin Professional Solar Powered Wi-Fi Weather Station Code: N23DQ, which I believe is a clone of the Ambient Weather WS-1001.

http://www.maplin.co.uk/p/maplin-professional-solar-powered-wi-fi-weather-station-n23dq



Recently the outside temperature overhead by about 10 degrees when the humidity is high, when its dry it goes back to normal, is it possible to replace the temperature sensor on the outside unit.?

Offline dupreezd

  • Forecaster
  • *****
  • Posts: 409
WS-1200-IP | ObserverIP | Meteobridge 3.5
WU, PWSWeather - KTXCONRO61
CWOP - FW0717
Blitzortung 2100

Offline Aircub

  • Member
  • *
  • Posts: 29
Re: Replacement parts for Ambient Weather WS-1001 Clone - Maplin N23DQ
« Reply #2 on: May 30, 2017, 03:41:03 AM »
Thanks will take a look at the sensors when I get a free moment.

Offline Rychu

  • Senior Member
  • **
  • Posts: 82
  • Type of station: HP1001WiFi & WH2600IP (WS1400IP)
    • Check on-line measurements and forecasts of Gdansk in Poland
Re: Replacement parts for Ambient Weather WS-1001 Clone - Maplin N23DQ
« Reply #3 on: August 19, 2017, 01:12:50 PM »
(...)  is it possible to replace the temperature sensor on the outside unit.?

Both stations use WH24 and WH24A (external) and WH25 and WH25A (internal) sensors - both are interchangeable. Important to be configured for the same frequency of 433 MHz or 866 MHz or 915 MHz. Typically, the sensors carry all three bands simultaneously.


Offline senrabyar

  • Member
  • *
  • Posts: 5
    • Ferryhill Station on Wunderground
Re: Replacement parts for Ambient Weather WS-1001 Clone - Maplin N23DQ
« Reply #5 on: October 28, 2017, 05:36:07 AM »
After the Ophelia 'storm' my humidity and temperature readings went totally mad.   

From my Maplin N23DQ, the sensor looks very different to others pictured.
 [ You are not allowed to view attachments ]

I replaced it with a  "SHT30-D Temperature Humidity Sensor Breakout 3.3v 5v For Arduino Arm RPi ESP8266"  I found on eBay.    The pins are not in the same order.
 [ You are not allowed to view attachments ]

Very pleased it is up and running - just hoping I have silicone sealed it well enough, although the sensor itself is exposed.   

Should the little circuit board be sprayed with something inert but water-repellent ?

Offline Aircub

  • Member
  • *
  • Posts: 29
Re: Replacement parts for Ambient Weather WS-1001 Clone - Maplin N23DQ
« Reply #6 on: October 28, 2017, 05:38:23 AM »
Can you give the Ebay link, my reading have gone haywire too.


Offline weatherist34

  • its just my hobby
  • Forecaster
  • *****
  • Posts: 507
    • Sinanoba Istanbul Home Weather Station
Re: Replacement parts for Ambient Weather WS-1001 Clone - Maplin N23DQ
« Reply #8 on: October 28, 2017, 05:51:32 AM »
After the Ophelia 'storm' my humidity and temperature readings went totally mad.   

From my Maplin N23DQ, the sensor looks very different to others pictured.
 [ You are not allowed to view attachments ]

I replaced it with a  "SHT30-D Temperature Humidity Sensor Breakout 3.3v 5v For Arduino Arm RPi ESP8266"  I found on eBay.    The pins are not in the same order.
 [ You are not allowed to view attachments ]

Very pleased it is up and running - just hoping I have silicone sealed it well enough, although the sensor itself is exposed.   

Should the little circuit board be sprayed with something inert but water-repellent ?

at the top of the radiation shield where it meets the rest of the unit apply silicon this also where the water tends to leak through , and can be problematic during dense fog.. self amalgamating tape from b&q or some plumbing shop in the uk or even maplins might sell it .just wrap a small piece around the circuit board leaving the sensor exposed..basically condensation does build up and sends your reading awol ..dew,water all act as a conductor !...brian

Offline senrabyar

  • Member
  • *
  • Posts: 5
    • Ferryhill Station on Wunderground
Re: Replacement parts for Ambient Weather WS-1001 Clone - Maplin N23DQ
« Reply #9 on: October 28, 2017, 06:07:42 AM »
Thanks for the detailed advice.

I have sealed the hole where the shield is attached to the main body of the PWS, and the hole through which the wire goes.  So I hope that water cannot be blown through the shield up into the batteries/electronics.

It was quite noticeable how dirty the old sensor was, but even after I had gently removed the grime with isopropanol, I could see apparent corrosion damage to the circuit board tracks (see my cleaned up picture showing where I had checked for continuity under the corrosion)

I suppose it is a perpetual problem - the sensor has to be in free flowing air, so it will get contaminated eventually (18 months in this case).



   

Offline weatherist34

  • its just my hobby
  • Forecaster
  • *****
  • Posts: 507
    • Sinanoba Istanbul Home Weather Station
Re: Replacement parts for Ambient Weather WS-1001 Clone - Maplin N23DQ
« Reply #10 on: October 28, 2017, 06:18:40 AM »
If you look the photo you can see the exposed solder points so only need a small amount of water or condensation across the solder points and it will go erratic , when I owned one I particularly paid attention to that area after addressing that area I had no more erratic readings regardless of heavy rain in our case flash floods and heavy dense fog I live 150 meters from the sea so prone to dense fog during the cooling months , in fact you can watch the fog flow through the air at times when it is really dense . I would definitely address that circuit board area .

Have fun and if you live in high UV area like here in Istanbul the wind vane will eventually break mine crumbled in my hand when I took it down a month ago..the plastic is not uv resistant and it just turned in a Bakelite powder literally as I touched it, if a bird sat on it would have broken long before.

Expected life of these models 3 years max and trash it sadly but they give you a good insight into the hobby.if I hadnít gave it away I would have salvaged the solar panel for another project ..


Brian

Offline dupreezd

  • Forecaster
  • *****
  • Posts: 409
Re: Replacement parts for Ambient Weather WS-1001 Clone - Maplin N23DQ
« Reply #11 on: October 28, 2017, 07:29:13 AM »
Quote
Should the little circuit board be sprayed with something inert but water-repellent ?

I use Conformal Coating Spray to seal my circuit boards and solder joints. You also get it in brush on which is great, as you don't have to mask items that must be left open such as the sensor opening.

« Last Edit: October 28, 2017, 07:30:48 AM by dupreezd »
WS-1200-IP | ObserverIP | Meteobridge 3.5
WU, PWSWeather - KTXCONRO61
CWOP - FW0717
Blitzortung 2100

Offline rods55555

  • Senior Member
  • **
  • Posts: 51
Re: Replacement parts for Ambient Weather WS-1001 Clone - Maplin N23DQ
« Reply #12 on: February 13, 2018, 07:26:36 PM »
Hi.
I have an Ambient Weather Clone (sold as MiSol).
For more than a month my outdoor unit is not reading the humidity correctly, always shows higher values than any other unit close to it, and at night it usually shows 99% humidity until sunrise, and sometimes the display shows - - %.
I read some topics about this problem, but it seems that Ambient Weather (and Fine Offset) doesn't sell spare parts (sensors). And I'm not going to buy a new outdoor unit just because one bad sensor.
Does anyone know if it's possible to find the sensor (OEM) to replace the bad one, or if there is a way to replace the sensor with another one, a "generic" sensor with the same specs?
I tried to remove the batteries and cover the solar panel to "reset" the unit, but it didnít make a difference. So, as the sensor is not working as it should, I tried to clean it by spraying clean water and let it dry, it didn't make a difference. So, I put three hygrometers close to the outdoor unit to know what the humidity was and I changed the calibration on the console, since the humidity today is something between 50% and 60% it seems to be "working", but I doubt it will read the correct humidity when it is really high.

 [ You are not allowed to view attachments ]
 [ You are not allowed to view attachments ]
 [ You are not allowed to view attachments ]

Offline senrabyar

  • Member
  • *
  • Posts: 5
    • Ferryhill Station on Wunderground
Re: Replacement parts for Ambient Weather WS-1001 Clone - Maplin N23DQ
« Reply #13 on: February 13, 2018, 08:59:49 PM »
See my earlier posts.   

Try to find the same little circuit board online - wherever you get it in the world it is so timy that the postage will only be the cost of a letter.

Good Luck !

Offline rods55555

  • Senior Member
  • **
  • Posts: 51
Re: Replacement parts for Ambient Weather WS-1001 Clone - Maplin N23DQ
« Reply #14 on: February 13, 2018, 09:08:09 PM »
See my earlier posts.   

Try to find the same little circuit board online - wherever you get it in the world it is so timy that the postage will only be the cost of a letter.

Good Luck !

Can I replace the original sensor with the SHT30 / SHT30-D board? Because the original sensor board I can't find it for sale.

Offline senrabyar

  • Member
  • *
  • Posts: 5
    • Ferryhill Station on Wunderground
Re: Replacement parts for Ambient Weather WS-1001 Clone - Maplin N23DQ
« Reply #15 on: February 14, 2018, 05:12:22 AM »
I replaced mine sucessfully. 
But please see my cautionary note on the wires not being in the same order.

Offline rods55555

  • Senior Member
  • **
  • Posts: 51
Re: Replacement parts for Ambient Weather WS-1001 Clone - Maplin N23DQ
« Reply #16 on: February 14, 2018, 08:56:32 PM »
I replaced mine sucessfully. 
But please see my cautionary note on the wires not being in the same order.

I bought two of those little boards. Now is just a matter of waiting (a lot of time) to get it here and also to learn which wire goes to which connection on the new sensor. It was really cheap, but the problem is that it takes 40 to 60 days for the awful, slow and corrupt Brazilian customs to release it from "their hands" .... that is the price to pay for being born in a third world country.  :?